View PLRXPL-SX-S43-22-N_4622149.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

COMMUNICATIONS MODULES & SUBSYSTEMS
10 G SFP+ 850 nm Limiting Transceiver, 10 Gigabit Ethernet Compliant PLRXPL-SX-S43-22-N Series
Key Features
* Compliant to industrywide, 10 G link specifications * Uses a highly reliable, 850 nm oxide VCSEL * Lead-free and RoHS 6/6-compliant, with allowed exemptions * Commercial case operating temperature 0 - 70C; extended temperature operating up to 85 * Single 3.3 V power supply * Low power consumption (typically 450 mW) * Bit error rate < 1 x 10-12 * Hot pluggable
Applications
* High-speed local area networks - Switches and routers - Network interface cards * Computer cluster crossconnect systems * Custom high-bandwidth data pipes
Compliance
* * * * * * * * * *
SFF 8431 Revision 3.2 SFF 8432 Revision 5.0 SFF 8472 Revision 10.3 IEEE 802.3 Clause 52 10GBASE-SR and 10GBASE-SW 10 G Fibre Channel CDRH and IEC60825-1 Class 1 Laser Eye Safety FCC Class B ESD Class 2 per MIL-STD 883 Method 3015 UL 94, V0 Reliability tested per Telcordia GR-468
The lead-free and RoHS-compliant small form factor pluggable (SFP+) transceiver from JDSU improves the performance for 10 Gigabit Ethernet (10 G) applications, and is ideal for high-speed, local area network applications. This transceiver features a highly reliable, 850 nm, oxide, vertical-cavity surface-emitting laser (VCSEL) coupled to an LC optical connector. The transceiver is fully compliant to 10GBASE-SR, 10GBASE-SW and 10 G Fibre Channel specifications, with internal AC coupling on both transmit and receive data signals. The all-metal housing design provides low EMI emissions in demanding 10 G applications and conforms to IPF specifications. An enhanced digital diagnostic feature set allows for realtime monitoring of transceiver performance and system stability, and the serial ID allows for customer and vendor system information to be stored in the transceiver. Transmit disable, loss-of-signal, and transmitter fault functions are also provided. The small size of the transceiver allows for high-density board designs that, in turn, enable greater total bandwidth.
NORTH AMERICA: 800 498-JDSU (5378)
WORLDWIDE: +800 5378-JDSU
WEBSITE: www.jdsu.com
10 G SFP+ 850 NM LIMITING TRANSCEIVER, 10 GIGABIT ETHERNET COMPLIANT
2 Section 1 Functional Description
The PLRXPL-SX-S43-22-N 10 G SFP+ 850 nm optical transceiver is designed to transmit and receive 64B/66B scrambled 10 G serial optical data over 50/125 m or 62.5/125 m multimode optical fiber.
Transmitter
The transmitter converts 64B/66B scrambled serial PECL or CML electrical data into serial optical data compliant with the 10GBASE-SR, 10GBASE-SW or 10 G Fibre channel standard. Transmit data lines (TD+ and TD-) are internally AC coupled, with 100 differential termination. Transmitter rate select (RS1) pin 9 is assigned to control the SFP+ module transmitter rate. It is connected internally to a 30 k pull-down resistor. A data signal on this pin does not affect the operation of the transmitter. An open collector-compatible transmit disable (Tx_Disable) is provided. This pin is internally terminated with a 10 k resistor to Vcc,T. A logic "1," or no connection, on this pin will disable the laser from transmitting. A logic "0" on this pin provides normal operation. The transmitter has an internal PIN monitor diode that ensures constant optical power output, independent of supply voltage. It is also used to control the laser output power over temperature to ensure reliability at high temperatures. An open collector-compatible transmit fault (Tx_Fault) is provided. The Tx_ Fault signal must be pulled high on the host board for proper operation. A logic "1" output from this pin indicates that a transmitter fault has occurred or that the part is not fully seated and the transmitter is disabled. A logic "0" on this pin indicates normal operation.
Receiver
The receiver converts 64B/66B scrambled serial optical data into serial PECL/CML electrical data. Receive data lines (RD+ and RD-) are internally AC coupled with 100 differential source impedance, and must be terminated with a 100 differential load. Receiver Rate Select (RS0) pin 7 is assigned to control the SFP+ module receiver rate. It is connected internally to a 30 k pull-down resistor. A data signal on this pin has no affect on the operation of the receiver. An open collector compatible loss of signal (LOS) is provided. The LOS must be pulled high on the host board for proper operation. A logic "0" indicates that light has been detected at the input to the receiver (see Optical characteristics, Loss of Signal Assert/Deassert Time). A logic "1" output indicates that insufficient light has been detected for proper operation.
10 G SFP+ 850 NM LIMITING TRANSCEIVER, 10 GIGABIT ETHERNET COMPLIANT
3
16 Transmitter Power Supply
10 k
3 Transmitter Disable In VCC_TX TX_DIS TD+ 18 Transmitter Positive Data
TOSA
Laser Driver
TX_GND TX_FAULT TD -
100
19 Transmitter Negative Data 2 Transmitter Fault Out 1, 17, 20 Transmitter Signal Ground
SCL
Management Processor
SDA
EEPROM
5 SCL Serial ID Clock 4 SDA Serial ID Data 6 MOD_ABS 15 Receiver Power Supply
VCC_RX
VCC_RX
RD -
50
12 Receiver Negative Data Out 13 Receiver Positive Data Out 8 Loss of Signal Out 9 RS1 TX Rate Select Not Functional on -N modules 7 RS0 RX Rate Select Not Functional on -N modules 10, 11, 14 Receiver Signal Ground
ROSA
RX_GND
Receiver
RD + RX_GND LOS 50
30 k
30 k
Figure 1
SFP+ optical transceiver functional block diagram
10 G SFP+ 850 NM LIMITING TRANSCEIVER, 10 GIGABIT ETHERNET COMPLIANT
4 Section 2
Vcc R1* 50
Application Schematic
10 k Receiver (Tx Fault) CMOS, TTL, or Open Collector Driver (Tx Disable) 1 VeeT VeeT 20
Z* = 100
PECL Driver (TX DATA)
R2* 50 Vcc 2 Tx Fault TD- 19
Rp*** Open Collector Bidirectional SDA Vcc
3 Tx Disable
TD+ 18 Power Supply Filter
4 SDA
VeeT 17 C3 C6
Rx L1 Vcc +3.3V Input
Rq Open Collector Bidirectional SCL
***
Vcc Vcc
5 SCL
VccT 16
L2 C2 C1
6 MOD_ABS
VccR 15 C4 C5 Ry
10 k Mod_ABS CMOS or TTL Driver (RS0 Rx Rate Select) Vcc 9 RS1 10 k Receiver (LOS) R6 CMOS or TTL Driver (RS1 Tx Rate Select) Vcc 10 VeeR R5 7 RS0
VeeR 14
8 LOS
RD+ 13 Z* = 100 RD12 R3* 50
VeeR 11
R4* 50
PECL Receiver (RX DATA)
Figure 2
Recommended application schematic for the 10 G SFP+ optical transceiver
Notes Power supply filtering components should be placed as close to the Vcc pins of the host connector as possible for optimal performance. PECL driver and receiver components will require biasing networks. Please consult application notes from suppliers of these components. CML I/O on the PHY are supported. Good impedance matching for the driver and receiver is required. SDA and SCL should be bi-directional open collector connections in order to implement serial ID in JDSU SFP+ transceiver modules. R1/R2 and R3/R4 are normally included in the output and input of the PHY. Please check the application notes for the IC in use. * Transmission lines should be 100 differential traces. Vias and other transmission line discontinuities should be avoided. In order to meet the host TP1 output jitter and TP4 jitter tolerance requirements it is recommended that the PHY has both transmitter pre-emphasis to equalize the transmitter traces and receiver equalization to equalize the receiver traces. With appropriate transmitter pre-emphasis and receiver equalization, up to 8 dB of loss at 5 GHz can be tolerated. ** R5 and R6 are required when an Open Collector driver is used in place of CMOS or TTL drivers. 5 k value is appropriate. *** The value of Rp and Rq depend on the capacitive loading of these lines and the two wire interface clock frequency. See SFF-8431. A value of 10 k is appropriate for 80 pF capacitive loading at 100 kHz clock frequency.
10 G SFP+ 850 NM LIMITING TRANSCEIVER, 10 GIGABIT ETHERNET COMPLIANT
5
Power supply filtering is recommended for both the transmitter and receiver. Filtering should be placed on the host assembly as close to the Vcc pins as possible for optimal performance. Vcc,R and Vcc,T should have separate filters. Power supply filter component values from Figure 2 are shown in the table below for two different implementations.
Power Supply Filter Component Values
Component L1, L2 Rx, Ry C1, C5 C2, C3, C4 C6
Option A 1.0 0.5* 10 0.1 Not required
Option B 4.7 0.5* 22 0.1 22
Units H F F F
Notes: Option A is recommended for use in applications with space constraints. Power supply noise must be less than 100 mVp-p. Option B is used in the module compliance board in SFF-8431. *If the total series resistance of L1+C6 and L2+C5 exceeds the values of Rx and Ry in the table, then Rx and Ry can be omitted.
10 G SFP+ 850 NM LIMITING TRANSCEIVER, 10 GIGABIT ETHERNET COMPLIANT
6 Section 3
* Section 3.1 * Section 3.2 * Section 3.3 * Section 3.4 * Section 3.5 * Section 3.6 * Section 3.7 * Section 3.8 * Section 3.9 * Section 3.10 * Section 3.11
Specifications
Technical specifications related to the SFP+ optical transceiver include: Pin Function Definitions Absolute Maximum Ratings Operating Conditions Electrical Characteristics Optical Characteristics Link Length Regulatory Compliance PCB Layout Front Panel Opening Module Outline Transceiver Belly-to-belly Mounting
3.1
Pin Function Definitions
11 12 13 14 15
TOWARD HOST WITH DIRECTION OF MODULE INSERTION
VEER VEER RDRD+ VEER VCCR VCCT VEET TD+ TDVEET RS1 RX_LOS RS0 MOD_ABS SCL SDA TX_DISABLE TX_FAULT VEET
10 9 8 7 6 5 4 3 2 1 TOWARD BEZEL
16 17 18 19 20
Figure 3
Host PCB SFP+ Pad assignment top view
10 G SFP+ 850 NM LIMITING TRANSCEIVER, 10 GIGABIT ETHERNET COMPLIANT
7
SFP+ Optical Transceiver Pin Descriptions
Pin Number Receiver 8
Symbol
Name
Description
LOS
Loss of Signal Out (OC)
10, 11, 14
VeeR
Receiver Signal Ground
12
RD-
Receiver Negative DATA Out (PECL) Receiver Positive DATA Out (PECL) Receiver Power Supply
13
RD+
15
VccR
7 Transmitter 3
RS0
RX Rate Select (LVTTL)
Sufficient optical signal for potential BER < 1x10-12 = Logic "0" Insufficient signal for potential BER < 1x10-12 = Logic "1" This pin is open collector compatible, and should be pulled up to Host Vcc with a 10 k resistor. These pins should be connected to signal ground on the host board. The VeeR and VeeT signals are connected together within the module and are isolated from the module case. Light on = Logic "0" Output Receiver DATA output is internally AC coupled and series terminated with a 50 resistor. Light on = Logic "1" Output Receiver DATA output is internally AC coupled and series terminated with a 50 resistor. This pin should be connected to a filtered +3.3 V power supply on the host board. See Application schematics on page 4 for filtering suggestions. This pin has an internal 30 k pull-down to ground. A signal on this pin will not affect module performance. Logic "1" Input (or no connection) = Laser off Logic "0" Input = Laser on This pin is internally pulled up to VccT with a 10 k resistor. These pins should be connected to signal ground on the host board. The VeeR and VeeT signals are connected together within the module and are isolated from the module case. Logic "1" Output = Laser Fault (Laser off before t_fault) This pin is open collector compatible, and should be pulled up to Host Vcc with a 10 k resistor. This pin should be connected to a filtered +3.3 V power supply on the host board. See Application schematics on page 4 for filtering suggestions. Logic "1" Input = Light on Transmitter DATA inputs are internally AC coupled and terminated with a differential 100 resistor. Logic "0" Input = Light on Transmitter DATA inputs are internally AC coupled and terminated with a differential 100 resistor. This pin has an internal 30 k pulldown to ground. A signal on this pin will not affect module performance. Serial ID with SFF 8472 Diagnostics. Module definition pins should be pulled up to Host Vcc with appropriate resistors for the speed and capacitive loading of the bus. See SFF8431. Serial ID with SFF 8472 Diagnostics. Module definition pins should be pulled up to Host Vcc with appropriate resistors for the speed and capacitive loading of the bus. See SFF8431. Pin should be pulled up to Host Vcc with 10 k resistor. MOD_ABS is asserted "high" when the SFP+ module is physically absent from the host slot.
TX_Disable
Transmitter Disable In (LVTTL)
1, 17, 20
VeeT
Transmitter Signal Ground
2
TX_Fault
Transmitter Fault Out (OC)
16
VccT
Transmitter Power Supply
18
TD+
Transmitter Positive DATA In (PECL) Transmitter Negative DATA In (PECL) TX Rate Select (LVTTL)
19
TD-
9
RS1
Module Definition 4 SDA
Two-wire Serial Data
5
SCL
Two-wire Serial Clock
6
MOD_ABS
Module Absent
10 G SFP+ 850 NM LIMITING TRANSCEIVER, 10 GIGABIT ETHERNET COMPLIANT
8
3.2 Absolute Maximum Ratings
Parameter Storage temperature Operating case temperature Relative humidity Transmitter differential input voltage Power supply voltage
Symbol TST TC RH VD VCC
Ratings -40 to +95 -40 to +85 5 - 95 (noncondensing) 2.5 0 to +4.0
Unit C C % V VP-P
Note: Absolute maximum ratings represent the damage threshold of the device. Damage may occur if the device is subjected to conditions beyond the limits stated here.
3.3
Operating Conditions
Part Number PLRXPL-SC-S43-xx-N PLRXPL-SE-S43-xx-N
Temperature Rating 0 - 70 -5 - 85
Unit C C
Note: Performance is not guaranteed and reliability is not implied for operation at any condition outside these limits.
10 G SFP+ 850 NM LIMITING TRANSCEIVER, 10 GIGABIT ETHERNET COMPLIANT
9
3.4 Electrical Characteristics
Parameter Supply voltage Power consumption Data rate Transmitter Supply current Common mode voltage tolerance Data dependent input jitter Data input uncorrelated jitter Data input total jitter Input data dependent pulse width shrinkage Eye mask
Symbol Vcc Pdiss
Min. 3.14
Typical 3.3 480 10.3125
Max. 3.47 1000 10.52 100
Unit V mW Gbps mA mVrms UI
Notes All electrical and optical specifications valid within this range BER < 1x10-12
IccT V DDJ Uj TJ DDPWS X1 X2 Y1 Y2 VIH VIL
15 0.10 0.023 0.28 0.055 0.12 0.33 95 2.0 -0.3 350 Vcc + 0.3 0.8 10 2 -50 -0.3 +37.5 0.4
29-1 pattern, TP1, at 10.3 Gbps (Note 1)
UI (rms) UI 231-1 pattern, TP1, BER < 1x10-12, at 10.3 Gbps (Notes 1, 8) UI Reference SFF-8431 Revision 3.2 UI UI mV mV V V s ms A V Reference SFF-8431 Revision 3.2, Figure 22. 5 x 10-5 hit ratio
Transmit disable voltage levels
Transmit disable/enable assert time TTD TTEN Transmit fault output levels IOH VOL
Transmit fault assert and reset times TFault TReset Initialization time Receiver Supply current Data output rise/fall time Output common mode voltage 99% jitter Total jitter Eye mask TINI IccR tr/tf
100 10 300 120 28 7.5 0.42
s s ms mA ps mVrms UI UI UI mV mV A V s s
Laser output disabled after TTD if input level is VIH; Laser output enabled after TTEN if input level is VIL Laser output disabled after TTD if input level is VIH; Laser output enabled after TTEN if input level is VIL Fault level is IOH and Laser output disabled TFault after laser fault. IOH is measured with a 4.7 k load to Vcc host. VOL is measured at 0.7 mA. Fault is VOL and Laser output restored TINI after disable is asserted for TReset, then disabled. After hot plug or Vcc 2.97 V
TJ X1 Y1 Y2 IOH VOL
0.70 0.35 200 -50 -0.3 425 +37.5 0.4 100 100
20% - 80%, differential RLOAD = 25 , common mode 231-1 pattern, TP4, at 10.3 Gbps (Notes 1, 4, 9) 231-1 pattern, TP4 , BER < 1x10-12, at 10.3 Gbps (Notes 1, 4, 8) Reference SFF-8431 Revision 3.2, Figure 23. 5 x 10-5 hit ratio LOS output level IOL TLOSD after light input > LOSD (Note 2) LOS output level VOH TLOSA after light input < LOSA (Note 2) LOS output level VOL TLOSD after light input > LOSD (Note 2) LOS output level VOH TLOSA after light input < LOSA (Note 2)
Loss of signal levels
Loss of signal assert/deassert time
TLOSA TLOSD
Note: All high frequency measurements are made with the module compliance board as described in SFF8431.
10 G SFP+ 850 NM LIMITING TRANSCEIVER, 10 GIGABIT ETHERNET COMPLIANT
10
3.5 Optical Characteristics
Parameter Transmitter Wavelength RMS spectral width Average optical power Optical modulation amplitude Transmitter dispersion penalty Relative intensity noise Receiver Wavelength Maximum input power Sensitivity (OMA) Stressed sensitivity (OMA) Loss of signal assert/deassert level Low frequency cutoff
Symbol p PAVG OMA TDP RIN12OMA Pmax S ISI = 3.5 dB LOSD LOSA FC
Min.
Typical
Max.
Unit
Notes
840 -7.3 *
850
860 0.45 Note 6 3.9 -128
nm nm dBm W dB dB/Hz nm dBm dBm dBm dBm dBm MHz
(Note 3) 12 dB reflection
840 +1
850
860 -11.1 -7.5 -11
-30 0.3
(Note 7) (Note 4) Chatter-free operation; LOSD is OMA, LOSA is average power -3 dB, P<-16 dBm
Note: * Tradeoffs between center wavelength, spectral width, and minimum OMA are used. Refer to the table on Minimum Optical Modulation Amplitude in dBm for details.
Minimum Optical Modulation Amplitude in dBm (from IEEE 802.3 Clause 52)
Center Wavelength (nm) 840 - 842 842 - 844 844 - 846 846 - 848 848 - 850 850 - 852 852 - 854 854 - 856 856 - 858 858 - 860
Up to 0.05 -4.2 -4.2 -4.2 -4.3 -4.3 -4.3 -4.3 -4.3 -4.3 -4.3
0.05 - 0.1 -4.2 -4.2 -4.2 -4.2 -4.2 -4.2 -4.2 -4.3 -4.3 -4.3
RMS Spectral Width (nm) 0.1 - 0.15 0.15 - 0.2 0.2 - 0.25 0.25 - 0.3 -4.1 -4.2 -4.2 -4.2 -4.2 -4.2 -4.2 -4.2 -4.2 -4.2 -4.1 -4.1 -4.1 -4.1 -4.1 -4.1 -4.1 -4.1 -4.1 -4.2 -3.9 -3.9 -4.0 -4.0 -4.0 -4.0 -4.0 -4.0 -4.0 -4.1 -3.8 -3.8 -3.8 -3.8 -3.8 -3.8 -3.9 -3.9 -3.9 -3.9
0.3 - 0.35 -3.5 -3.6 -3.6 -3.6 -3.6 -3.6 -3.7 -3.7 -3.7 -3.7
0.35 - 0.4 -3.2 -3.3 -3.3 -3.3 -3.3 -3.4 -3.4 -3.4 -3.5 -3.5
0.4 - 0.45 -2.8 -2.9 -2.9 -2.9 -3.0 -3.0 -3.1 -3.1 -3.1 -3.2
Note: * Tradeoffs between center wavelength, spectral width, and minimum OMA are used.
10 G SFP+ 850 NM LIMITING TRANSCEIVER, 10 GIGABIT ETHERNET COMPLIANT
11
3.6 Link Length
Data Rate Standard 10.3 GBd
Fiber Type 62.5/125 m MMF 50/125 m MMF 50/125 m MMF 50/125 m MMF 50/125 m MMF
Modal Bandwidth at 850 nm (MHz*km) 200 500 900 1500 2000
Distance Range (m) 0.5 - 33 0.5 - 82 0.5 - 150 0.5 - 240 0.5 - 300
Notes 5 5 5 5 5
Specification Notes
1. UI (unit interval): one UI is equal to one bit period. For example, 10.3125 Gbps corresponds to a UI of 96.97 ps. 2. For LOSA and LOSD definitions, see Loss of Signal Assert/Deassert Level in Optical Characteristics. 3. Transmitter dispersion penalty is measured using the methods specified in the IEEE standard 802.3-2005 Clause 52. 4. Measured with stressed eye pattern as per IEEE standard 802.3-2005, Clause 52. 5. Distances, shown in the "Link Length" table, are calculated for worst-case fiber and transceiver characteristics based on the optical and electrical specifications shown in this document using techniques specified in IEEE 802.3. These distances are consistent with those specified for 10GBASE-SR and 10GBASE-SW. In the nominal case, longer distances are achievable. 6. The maximum transmitter output power is the lesser of the Class 1 laser eye safety limit and -1 dBm (the maximum receiver input power limit per the IEEE 802.3 Clause 52 specification). 7. Sensitivity is for informational purposes only. 8. The data pattern for the total jitter measurement is one of IEEE 802.3 Clause 52.9 Pattern 1, Pattern 3, or valid 64B/66B data traffic. 9. 99% jitter is as defined in SFF-8431 Revision 3.2. 99% jitter has the same definition as "all but 1% for jitter" as used in IEEE 802.3 Clause 52.9.9 and is defined as the time from the 0.5th to the 99.5th percentile of the jitter histogram.
10 G SFP+ 850 NM LIMITING TRANSCEIVER, 10 GIGABIT ETHERNET COMPLIANT
12
3.7 Regulatory Compliance
The PLRXPL-SX-S43-22-N optical transceiver complies with international Electromagnetic Compatibility (EMC) and international safety requirements and standards. EMC performance is dependent on the overall system design. Information included herein is intended as a figure of merit for designers to use as a basis for design decisions. The PLRXPL-SX-S43-22-N optical transceiver is lead-free and RoHS-compliant per Directive 2002/95/EC of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment.
Regulatory Compliance
Feature Component safety
Test Method UL 60950 UL 94, V0 IEC 60950 Directive 2002/95/EC
Performance UL File E209897 TUV Report/Certificate (CB scheme) Compliant per the Directive 2002/95/EC of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment. TUV Certificate CDRH compliant and Class 1 laser eye safe Noise frequency range: 30 MHz to 40 GHz. Good system EMI design practice required to achieve Class B margins.
RoHS-compliant
Laser eye safety1 Electromagnetic Compatibility Electromagnetic emissions
EN 60825 U. S. 21CFR 1040.10 EMC Directive 89/336/EEC FCC CFR47 Part 15 IEC/CISPR 22 AS/NZS CISPR22 EN 55022 ICES-003, Issue 4 VCCI-03 EMC Directive 89/336/EEC IEC/CISPR/24 EN 55024 EN 61000-4-2
Electromagnetic immunity
ESD immunity
Radiated immunity
EN 61000-4-3
Exceeds requirements. Withstand discharges of 4 kV contact and 8 kV air discharge to Criterion A, and 8 kV contact and 25 kV air discharge to Criterion B. Exceeds requirements. Field strength of 10 V/m RMS, from 10 MHz to 1 GHz. No effect on transmitter/receiver performance is detectable between these limits.
1. For further details, see Eye Safety
10 G SFP+ 850 NM LIMITING TRANSCEIVER, 10 GIGABIT ETHERNET COMPLIANT
13
3.8 PCB Layout
Figure 4
Board layout
ALL DIMENSIONS ARE IN MILLIMETERS
Figure 5
Detail layout
10 G SFP+ 850 NM LIMITING TRANSCEIVER, 10 GIGABIT ETHERNET COMPLIANT
14
3.9 Front Panel Opening
Figure 6
3.10
Module Outline
ALL DIMENSIONS ARE IN MILLIMETERS
Figure 7
10 G SFP+ 850 NM LIMITING TRANSCEIVER, 10 GIGABIT ETHERNET COMPLIANT
15
3.11 Transceiver Belly-to-belly Mounting
Figure 8
10 G SFP+ 850 NM LIMITING TRANSCEIVER, 10 GIGABIT ETHERNET COMPLIANT
16 Section 4
* Section 4.1 * Section 4.2 * Section 4.3 * Section 4.4
Related Information
Other information related to the SFP+ optical transceiver includes: Digital diagnostic monitoring and serial ID operation Package and handling instructions ESD discharge (ESD) Eye safety
4.1
Digital Diagnostic Monitoring and Serial ID Operation
The PLRXPL-SX-S43-22-N optical transceiver is equipped with a two-wire serial EEPROM that is used to store specific information about the type and identification of the transceiver as well as real-time digitized information relating to the transceiver's performance. See the Small Form Factor Committee document number SFF-8472 Revision 10.3, dated December 1, 2007 for memory/address organization of the identification data and digital diagnostic data. The enhanced digital diagnostics feature monitors five key transceiver parameters which are internally calibrated and should be read as absolute values and interpreted as follows:
Transceiver Temperature in degrees Celsius: Internally measured. Represented as
a 16 bit signed two's complement value in increments of 1/256C from -40 to +85C with LSB equal to 1/256C. Accuracy is 3C over the specified operating temperature and voltage range.
Vcc/Supply Voltage in Volts: Internally measured. Represented as a 16-bit unsigned
integer with the voltage defined as the full 16-bit value(0 - 65535) with LSB equal to 100 uV with a measurement range of 0 to +6.55 V. Accuracy is three percent of nominal value over the specified operating temperature and voltage ranges.
TX Bias Current in mA: Represented as a 16-bit unsigned integer with current de-
fined as the full 16-bit value (0 - 65535) with LSB equal to 2 uA with a measurement range of 0 - 131 mA. Accuracy is 10 percent of nominal value over the specified operating temperature and voltage ranges.
TX Output Power in mW: Represented as a 16-bit unsigned integer with the power defined as the full 16-bit value (0 - 65535) with LSB equal to 0.1 uW. Accuracy is 2 dB over the specified temperature and voltage ranges over the range of -7 dBm to -1 dBm. Data is not valid when transmitter is disabled. RX Received Optical Power in mW: Represented as average power as a 16-bit un-
signed integer with the power defined as the full 16-bit value (0 - 65535) with LSB equal to 0.1 uW. Accuracy is 3 dB over the specified temperature and voltage ranges over the power range of -12 dBm to 0 dBm.
10 G SFP+ 850 NM LIMITING TRANSCEIVER, 10 GIGABIT ETHERNET COMPLIANT
17
Reading the data
The information is accessed through the SCL and SDA connector pins of the module. The SFF-8431 Revision 3.2 specification contains all the timing and addressing information required for accessing the data in the EEPROM. The device address used to read the Serial ID data is 1010000X(A0h), and the address to read the diagnostic data is 1010001X(A2h). Any other device addresses will be ignored. MOD_ABS, pin 6 on the transceiver, is connected to Logic 0 (Ground) on the transceiver. SCL, pin 5 on the transceiver, is connected to the SCL pin of the EEPROM. SDA, pin 4 on the transceiver, is connected to the SDA pin of the EEPROM. The EEPROM Write Protect pin is internally tied to ground with no external access, allowing write access to the customer-writable field (bytes 128 - 247 of address 1010001X). Note: address bytes 0 - 127 are not write protected and may cause diagnostic malfunctions if written over.
Decoding the data
The information stored in the EEPROM, including the organization and the digital diagnostic information, is defined in the Small Form Factor Committee document SFF-8472 Revision 10.3, dated December 1, 2007.
Data Field Descriptions
Address( 1010000X)(A0h) 0
Serial ID Information; Defined by SFP MSA
Address( 1010001X)(A2h) 0 55 95
Alarm and Warning Limits Reserved for External Calibration Constants Real Time Diagnostic Information JDSU-Specific Information Nonvolatile, customerwriteable, field-writeable area
95
JDSU-Specific Information
119 127
127
Reserved for SFP MSA
247 255 255
JDSU-Specific Information
10 G SFP+ 850 NM LIMITING TRANSCEIVER, 10 GIGABIT ETHERNET COMPLIANT
18
Serial ID Data and Map
Memory Address 0 1 2 3-10 11 12 13 14 15 16 17 18 19 20-35 36 37-39 40-55 56-59 60-61 62 63 64 65 66 67 68-83 84-91 92 93 94 95 96-127 128-255
Value 03 04 07 1000000020400C80 06 67 00 00 00 08 03 00 1E JDSU 00 00019C PLRXPLSxS43xxN 0352 CC_BASE 00 1A 00 00
Comments SFP Transceiver SFP with Serial ID LC Connector 64B/66B Nominal Bit rate of 10.3 Gbps Rate Identifier (for Rate-selectable modules) Single-mode fiber not supported Single-mode fiber not supported 82 meters of OM2 50/125 m multimode fiber 33 meters of OM1 62.5/125 m multimode fiber Copper not supported 300 meters of OM3 50/125 m multimode fiber Vendor Name (ASCII) Reserved IEEE Company ID (ASCII) Part Number (ASCII), x = part number variable Revision of part number (ASCII) Wavelength of laser in nm; 850 Unallocated Check Code; Lower 8 bits of sum from byte 0 through 62 Conventional uncooled laser, Class 1 power level, Conventional limiting receiver output Tx_Disable, Tx Fault, Loss of Signal implemented
68 F0 03 CC_EXT
Serial Number (ASCII) Date Code (ASCII) Diagnostic monitoring implemented, internally calibrated, Receiver Power Measurement type is Average Power Alarms and Warnings, TX_Fault and Rx_LOS monitoring implemented, TX_Disable Control and Monitoring. SFF-8472 Revision 10.3 compliant Check Code; Lower 8 bits of sum from byte 64 through 94 JDSU-specific EEPROM Reserved for SFF-8079
10 G SFP+ 850 NM LIMITING TRANSCEIVER, 10 GIGABIT ETHERNET COMPLIANT
19
Diagnostics Data Map
Memory Address 00-01 02-03 04-05 06-07 08-09 10-11 12-13 14-15 16-17 18-19 20-21 22-23 24-25 26-27 28-29 30-31 32-33 34-35 36-37 38-39 40-55 56-59 60-63 64-67 68-71 72-75 76-77 78-79 80-81 82-83 84-85 86-87 88-89 90-91 92-94 95 96 97 98 99 100
Value Temp High Alarm Temp Low Alarm Temp High Warning Temp Low Warning Voltage High Alarm Voltage Low Alarm Voltage High Warning Voltage Low Warning Bias High Alarm Bias Low Alarm Bias High Warning Bias Low Warning TX Power High Alarm TX Power Low Alarm TX Power High Warning TX Power Low Warning RX Power High Alarm RX Power Low Alarm RX Power High Warning RX Power Low Warning Reserved RP4 RP3 RP2 RP1 RP0 Islope Ioffset TPslope TPoffset Tslope Toffset Vslope Voffset Reserved Checksum Temperature MSB Temperature LSB Vcc MSB Vcc LSB TX Bias MSB (Note 1)
Comments MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address For future monitoring quantities External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant Reserved Low order 8 bits of sum from 0 - 94 Internal temperature AD values Internally measured supply voltage AD values TX Bias Current AD values
10 G SFP+ 850 NM LIMITING TRANSCEIVER, 10 GIGABIT ETHERNET COMPLIANT
20
Diagnostics Data Map (continued)
Memory Address 101 102 103 104 105 106 107 108 109 110-7 110-6 110-5 110-4 110-3 110-2 110-1 110-0 111 112-119 120-127 128-247 248-255
Value TX Bias LSB (Note 1) TX Power MSB (Note 1) TX Power LSB (Note 1) RX Power MSB RX Power LSB Reserved MSB Reserved LSB Reserved MSB Reserved LSB Tx Disable State Soft Tx Disable Control Reserved Rate Select State Soft Rate Select Control Tx Fault State LOS State Data Ready State Reserved Optional alarm & warning flag bits (Note 2) Vendor specific User/Customer EEPROM Vendor specific
Comments
Measured TX output power AD values Measured RX input power AD values For 1st future definition of digitized analog input For 2nd future definition of digitized analog input Digital State of Tx Disable Pin Writing "1" OR pulling the Tx_Disable pin will disable the laser Digital State of Rate Select Pin Writing to this bit has no effect Digital State Digital State Digital State; "1" until transceiver is ready Reserved Refer to SFF-8472 Revision 10.3 JDSU specific Field writeable EEPROM Vendor specific control
Note : 1. During Tx disable, Tx bias and Tx power will not be monitored. 2. Alarm and warning are latched. The flag registers are cleared when the system Reads AND the alarm/warning condition no longer exists.
10 G SFP+ 850 NM LIMITING TRANSCEIVER, 10 GIGABIT ETHERNET COMPLIANT
21
4.2 Package and Handling Instructions
This product is not compatible with any aqueous wash process.
Process plug
The PLRXPL-SX-S43-22-N optical transceiver is supplied with a process plug. This plug protects the transceiver's optics during standard manufacturing processes by preventing contamination from air borne particles. Note: It is recommended that the dust cover remain in the transceiver whenever an optical fiber connector is not inserted.
Recommended cleaning and de-greasing chemicals
JDSU recommends the use of methyl, isopropyl and isobutyl alcohols for cleaning. Do not use halogenated hydrocarbons (trichloroethane, ketones such as acetone, chloroform, ethyl acetate, MEK, methylene chloride, methylene dichloride, phenol, N-methylpyrolldone).
Flammability
The housing is made of cast zinc and sheet metal.
4.3 Electrostatic Discharge (ESD)
Handling
Normal ESD precautions are required during the handling of this module. This transceiver is shipped in ESD protective packaging. It should be removed from the packaging and handled only in an ESD protected environment utilizing standard grounded benches, floor mats, and wrist straps.
Test and operation
In most applications, the optical connector will protrude through the system chassis and be subjected to the same ESD environment as the system. Once properly installed in the system, this transceiver should meet and exceed common ESD testing practices and fulfill system ESD requirements. Typical of optical transceivers, this module's receiver contains a highly sensitive optical detector and amplifier which may become temporarily saturated during an ESD strike. This could result in a short burst of bit errors. Such an event may require the application to reacquire synchronization at the higher layers (serializer/ deserializer chip).
10 G SFP+ 850 NM LIMITING TRANSCEIVER, 10 GIGABIT ETHERNET COMPLIANT
4.4 Eye Safety
The PLRXPL-SX-S43-22-N Optical Transceiver is a CLASS 1 LASER PRODUCT as defined by the international standard IEC 60825-1 Second Edition 2007-03 and by U.S.A. regulations for Class 1 products per CDRH 21 CFR 1040.10 and 1040.11. Laser emissions from Class 1 laser products are not considered hazardous when operated according to product specifications. Operating the product with a power supply voltage exceeding 4.0 volts may compromise the reliability of the product, and could result in laser emissions exceeding Class 1 limits.
Caution
Tampering with this laser based product or operating this product outside the limits of this specification may be considered an act of "manufacturing," and will require, under law, recertification of the modified product with the U.S. Food and Drug Administration (21 CFR 1040). The use of optical instruments with this product will increase eye hazard.
Ordering Information
For more information on this or other products and their availability, please contact your local JDSU account manager or JDSU directly at 1-800-498-JDSU (5378) in North America and +800-5378-JDSU worldwide, or via e-mail at customer.service@jdsu.com.
Sample: PLRXPL-SC-S43-22-N
Part Number PLRXPL-SC-S43-22-N PLRXPL-SE-S43-22-N Product Description 10 G SFP+ SR compliant, limiting electrical interface, 0 - 70C, 5% Vcc, no rate select, generic 10 G SFP+ SR compliant, limiting electrical interface, -5 - 85C, 5% Vcc, no rate select, generic
NORTH AMERICA: 800 498-JDSU (5378)
WORLDWIDE: +800 5378-JDSU
WEBSITE: www.jdsu.com
Product specifications and descriptions in this document subject to change without notice. (c) 2008 JDS Uniphase Corporation 30162598 000 1208 PLRXPL-SX-S43-22-N.DS.CMS.AE
December 2008

▲Up To Search▲

Price & Availability of PLRXPL-SX-S43-22-N

	To Download PLRXPL-SX-S43-22-N Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .